Optima超速離心機轉頭適配離心管
Optima XE-100/90超速離心機VTi 90 VTi 65.2垂直轉頭
VTi 90、VTi 65.2垂直轉頭離心2.0mL g-MAX管、4.9mL指封管及5.1mL熱封管,常用于質粒DNA純化或蛋白質的密度梯度離心。適用于Optima XPN-100/XPN-90/XPN-80和Optima XE-100/XE-90系列超速離心機。
商品名稱:VTi 90 VTi 65.2垂直轉頭 Vertical-Tube Rotor
制 造 商:美國貝克曼庫爾特(Beckman Coulter)公司
品 牌:Beckman
轉頭配套適配器、離心管見:[訂購信息]
詳細描述
VTi 90、VTi 65.2垂直轉頭由鈦合金制成,可離心2.0 – 5.1mL樣品管,常用于質粒DNA純化或蛋白質的密度梯度離心。適用于貝克曼庫爾特高端Optima XPN-100/XPN-90/XPN-80型立式離心機和基礎型Optima XE-100/XE-90超速離心機。
1、轉頭組件
轉頭由鈦合金制成,并涂有黑色聚氨酯(polyurethane)漆。
Quick-Seal和OptiSeal兩款離心管,需添加管蓋狀的管帽墊片/墊片(tube spacer)對離心管上部提供支撐,避免在強大水平離心力作用下,離心管上部變形。黑色適配器用于Quick-Seal熱封管,金色適配器用于OptiSeal管。
超速離心機運行中,為避免因離心管內殘留少量空氣因直接暴露于離心腔體的真空環境而過度膨脹、離心管變形引發樣品泄漏風險,需將離心孔內的氣壓維持在實驗室正常氣壓水平。轉頭標配的黑色陽極氧化鋁材質六邊形轉頭塞(hex-cavity rotor plug)與密封墊圈(plug gasket),用于有效密封離心孔,將離心管與離心腔真空環境有效隔離。
為了防止超速,超速離心機中的光電探測器會監測轉頭底部的超速盤,如果檢測到速度超過額度轉速,則自動中止運行。
2、轉頭準備(Rotor Preparation)
在非室溫條件的離心,需事先在冰箱中預冷或恒溫箱體內將轉頭加熱轉頭到指定溫度備用。
確保轉頭塞螺紋清潔,并用潤滑劑 (306812) 均勻潤滑,以最大限度地減少螺紋摩損,確保有效密封。
將轉頭固定在轉頭鉗臺(rotor vise342705)中,鉗臺應用螺栓固定或夾緊在剛性操作臺面上。
將已填充的樣品管、連同正確的適配器墊片、轉頭塞對稱地裝入轉頭。樣品管裝入離心孔后,還應在管上方添加管帽墊片墊片(和浮置墊片,如果適用的話)完成裝載。
每個離心管適配器墊片上插入一個轉頭塞(墊圈端朝下),使用 T40 Torx轉頭塞配套適配器(T40 Torx adapter),用扭矩扳手(torque wrench 369791)擰緊塞的同時,向下按壓六角轉頭塞適配器以免打滑。將每個轉頭塞擰緊至 13.6 N?m,使轉頭塞的頂面略低于轉頭表面即可。
3、樣品取出回收(Removal and Sample Recovery)
將VTi 65.2垂直轉頭轉頭從離心機垂直向上托起離開驅動軸取出后,重新固定于鉗臺,并用扭矩扳手和轉頭塞適配器解封離心孔。
使用適當?shù)牟鹦豆ぞ咭瞥龎|片和管子。
4、轉頭技術規格
轉頭型號 | VTi 90 | VTi 65.2 |
最高轉速 | 90000 rpm | 65000 rpm |
最高轉速時溶液額定密度 (Density rating at maximum speed) | 1.7 g/mL | |
最高轉速時相對離心場(Relative Centrifugal Field) | ||
最大離心半徑/最大離心力 | Rmax (71.1 mm)/645000×g | Rmax (87.9 mm)/416000×g |
平均離心半徑/平均離心力 | Rav (64.5 mm)/585000×g | Rav (81.3 mm)/385000×g |
最小離心半徑/最小離心力 | Rmin (57.9 mm)/525000×g | Rmin (74.7 mm)/353000×g |
最大速度下 k 系數(k factor) | 6 | 10 |
額定離心管尺寸 (Nominal tube dimensions) | 13×51 mm | |
額定離心容量(Nominal tube capacity) | 8×5.1 mL | 16×5.1mL |
達到最大速度的近似加速時間(滿載) | 9.0 min | 11.0 min |
從最大速度(滿載)開始的減速時間 | 8.5 min | 8.0 min |
滿載轉頭重量 | 5.5 kg | 8.5 kg |
轉頭的材質 | 鈦合金 |
5、轉頭適配離心管
VTi 90 和VTi 65.2垂直轉頭的一次性指封管和熱封管(標準配置不含離心管,需單獨訂購)可通用。
為實現離心管有效密封,Quick-Seal管的密封需采用管蓋熱密封器(Cordless Tube Topper)工作套件操作。
熱封管離心結束后,需使用浮置墊片提取工具(Floating spacer removal tool 338765)、離心管提取工具(Tube Removal Tool, 361668),從離心孔中取出管帽墊片(spacers)和離心管。
訂購信息
品名 | 品牌 | 貨號 | 規格 | 描述 | 報價 |
VTi 90垂直轉頭套件 | Beckman | 362751 | set | VTi 90 Vertical-Tube Rotor Package Standard accessories includes: 1x 342705 Rotor Vise 1x 858121 Torque Wrench 1x 976959 Torx Wrench Adapter 1x 306812 Spinkote Lubricant 2x 355539 Over-speed Disk 12x 342882 Rotor Plug Gaskets | 詢價 詢價 |
5.1mL熱封管工作套裝 | Beckman | 360979 | set | 5.1mL Polypropylene Quick-Seal Tube Kit Applicable Ultracentrifuge Rotor: VTi 90/NVT 90 includes: 4盒 342412 Quick-Seal Polypropylene Tubes 8個 342883 Spacers 1個 348122 Tube Rack 1個 361668 Tube Extraction Tool Cordless Tube Topper Kit required | 詢價 詢價 |
4.9mL指封管工作套裝 | Beckman | 360970 | set | 4.9mL Polypropylene OptiSeal Tube Kit Applicable Ultracentrifuge Rotor: VTi 90/NVT 90 includes: 4盒 362185 OptiSeal Polypropylene Tubes 8個 362198 Spacers 1個 361638 Tube Rack 1個 361668 Tube Extraction Tool 1個 338765 Spacer Removal Tool | 詢價 詢價 |
2mL g-Max管工作套裝 | Beckman | 357325 | set | 2 mL Quick-Seal Polypropylene Tube Kit Applicable Ultracentrifuge Rotor: VTi 90/NVT 90 includes: 50個 2mL g-Max快封管 345829 8個 管帽適配器 342883 1個 g-Max取管鑷子 878446 1個 取帽工具 338765 | 詢價 詢價 |
VTi 65.2垂直轉頭套件 | Beckman | 362754 | set | VTi 65.2 Vertical-Tube Rotor Package Standard accessories includes: 1x 342705 Rotor Vise 1x 858121 Torque Wrench 1x 976959 Torx Wrench Adapter 1x 306812 Spinkote Lubricant 2x 330338 Over-speed Disks 12x 342882 Rotor Plug Gaskets | 詢價 詢價 |
5.1mL熱封管工作套裝 | Beckman | 360977 | set | 5.1mL Polypropylene Quick-Seal Tube Kit Applicable Ultracentrifuge Rotor: NVT 65.2/VTi 65.2 includes: 4盒 342412 Quick-Seal Polypropylene Tubes 16個 342883 Spacers 1個 348122 Tube Rack 1個 361668 Tube Extraction Tool (Cordless Tube Topper Kit required) | 詢價 詢價 |
4.9mL指封管工作套裝B | Beckman | 360972 | set | 4.9mL Polypropylene OptiSeal Tube Kit Applicable Ultracentrifuge Rotor: NVT 65.2/VTi 65.2 includes: 4盒 362185 OptiSeal Polypropylene Tubes 16個 362198 Spacers 1個 361638 Tube Rack 1個 361668 Tube Extraction Tool 1個 338765 Spacer Removal Tool | 詢價 詢價 |
2mL g-Max管工作套裝 | Beckman | 357326 | set | 2 mL Quick-Seal Polypropylene Tube Kit Applicable Ultracentrifuge Rotor: NVT 65.2/VTi 65.2 includes: 50個 2mL g-Max快封管 345829 16個 管帽適配器 342883 1個 g-Max取管鑷子 878446 1個 取帽工具 338765 | 詢價 詢價 |
5.1mL超凈熱封管 | Beckman | 344075 | 50/pkg | 5.1mL Quick-Seal Round-Top Ultra-Clear Tube Nominal Size: 13×51mm - 50Pk Applicable Ultracentrifuge Rotor: NVT 90, NVT 65.0 Required Quick-Seal Tube Spacer: 342883 | 詢價 詢價 |
5.1mL熱封管 | Beckman | 342412 | 50/pkg | 5.1mL Quick-Seal Round-Top Polypropylene Tube Nominal Size: 13 x 51mm - 50Pk | 詢價 詢價 |
Φ13mm管帽墊片 | Beckman | 342883 | 1/pkg | 13mm Diameter Aluminum Tube Spacer | 詢價 詢價 |
Φ13mm離心管架 | Beckman | 348122 | 1/pkg | Tube Rack for 13.0mm Diameter Tubes Applicable Ultracentrifuge Rotor: TLA-110, TLA-100.3,TLN-100 | 詢價 詢價 |
2mL熱封管 | Beckman | 345829 | 50/pkg | 2mL Quick-Seal g-max Polypropylene Tube Nominal Size: 13×25mm - 50Pk Applicable Ultracentrifuge Rotor: Type 100 T, Type 50.4 Ti Required Spacer: 360270 | 詢價 詢價 |
Φ13mm管帽墊片 | Beckman | 342883 | 1/pkg | 13mm Diameter Aluminum Tube Spacer | 詢價 詢價 |
Φ13mm浮置墊片 | Beckman | 345827 | 1Pk | 13mm Diameter Noryl Bell-Top Tube Floating Spacer | 詢價 詢價 |
Φ13mm離心管架 | Beckman | 348122 | 1/pkg | Tube Rack for 13.0mm Diameter Tubes Applicable Ultracentrifuge Rotor: TLA-110, TLA-100.3,TLN-100 | 詢價 詢價 |
-
Optima XE-100/90超速離心機SW 41 Ti甩平轉頭
6×13.2mL|41000rpm
-
Open-Top管加蓋工具
open-top管蓋鉗臺|六角扳手
-
MAX-XP臺式超速離心機4×2.2mL水平轉頭TLS-55
4×2.2mL|55000rpm/水平轉頭
-
MAX-XP臺式超速離心機4×5mL水平轉頭MLS-50
4×5.0mL|50000rpm/水平轉頭
-
MAX-XP臺式超速離心機MLN-80近垂直轉頭
8×8.0mL|80000rpm/NVT
-
MAX-XP臺式超速離心機TLN-100近垂直轉頭
8×3.9 mL|100000rpm
-
MAX-XP臺式超速離心機角轉頭MLA-50
6×32.4 mL|50000rpm
-
MAX-XP臺式超速離心機角轉頭MLA-55
8×13.5 mL|55000rpm
-
MAX-XP臺式超速離心機角轉頭MLA-80
8×8.0mL|80000rpm